630℃超超临界二次再热塔式锅炉热力特性与壁温耦合计算研究

630℃超超临界火电技术作为下一代超超临界发电技术,对于煤炭资源的节约、发电机组的经济性以及环境改善,都显示了优越性。目前630℃超超临界锅炉的热力计算还缺乏相关研究。本文以某1000MW超超临界二次再热塔式锅炉布置方案为例,将锅炉管道、炉膛、高温受热面作为串联管路计算,在工质侧将热力计算与管路计算进行耦合建立数值分析模型。该计算模型能够同时得到比实现水动力和热力计算更精细的结果,对后续700℃工程持续优化提升做好技术储备。     

增材制造技术在超高膨胀封隔器中的应用

石油和天然气行业不断关注增材制造技术在航空航天和汽车行业的应用发展。研发了利用增材制造技术的超高膨胀封隔器,该封隔器的支承环系统由增材制造。增材制造设计大幅减少了支承系统的构件数量,同时显著提高了膨胀能力和额定压力。密封元件系统与增材制造支承环安装在一起,提供了极端膨胀比、零挤压间隙和对不规则孔的良好适应性。分析和测试结果表明:直径膨胀比高达111%,与常规封隔器相比,提高50%以上; 至少涵盖5种线重的套管(外径相同); 在148.89 ℃的温度下,密封元件能够保持压力68.95 MPa。介绍了增材制造技术、增材制造支承环概念、增材制造材料力学性能、密封元件系统优化和测试情况,以期给我国的完井作业提供借鉴。     

PAN纤维共聚单体作用机理的光电离质谱研究

本工作以丙烯腈/衣康酸（IA）二元共聚原丝以及丙烯腈/IA/丙烯酸甲酯（MA）三元共聚原丝为研究对象，利用热重分析仪（TG）和热解-同步辐射真空紫外光电离质谱（Py-SVUV-PIMS）对其热稳定化过程进行研究。TG结果表明，氮气气氛下，二元共聚原丝（PAN/IA）和三元共聚原丝（PAN/IA/MA）分别呈现三阶段和两阶段的热分解过程，其中PAN/IA的第一和第二阶段均对应PAN线型分子链的断裂，但前者是由自由基环化反应放热引发的，后者则是由正常温度下的热分解所致，而单体MA的加入显著抑制了自由基环化反应，使得PAN原丝的热稳定化能够以单体IA诱导的离子型环化反应为主较平缓地进行，相应的热失重过程也由两阶段转变为了单阶段。Py-SVUV-MS的实验结果表明，两种共聚PAN原丝在程序升温过程中会生成包括含氮小分子、丙烯腈单体及低聚物、成环化合物在内的三类主要热解产物，对比各类产物的生成趋势和产量，推断单体MA通过降低PAN结构的规整度，使其无定形化，从而增加环化反应的引发点，促进PAN原丝向稳定的预氧丝转变，同时由典型热解产物——甲基丙烯腈的生成路径可知，MA本身并不参与PAN大分子的环化反应，属于中性共聚单体。空气气氛下，CO₂的产量差异也间接证明了MA单体能够有效提升PAN纤维的固碳能力，采用三元共聚方法制得的PAN纤维热稳定性能更佳。     

基于双向流固耦合弹性环式挤压油膜阻尼器建模及动力学特性研究

利用数值方法建立了弹性环式挤压油膜阻尼器(ERSFD)的流固耦合模型,分别利用有限元方法以及有限体积法建立了弹性环和内外油膜的CFD数值模型,并进一步利用分时迭代的弱耦合方法实现了油膜以及弹性环控制方程的耦合求解,获得了内油膜的压力分布特性及弹性环的变形,并进一步识别了油膜和弹性环的动力学特性系数;研究了涡动频率、凸台数目、凸台高度、凸台宽度以及弹性环厚度对阻尼器动力学特性系数的影响。结果表明,弹性环的凸台高度对ERSFD油膜动力学特性系数的影响最为明显,ERSFD油膜阻尼与涡动频率无关。     

Numerical evaluation and the effects of geometrical and operational parameters on thermal performance of the shell and double coil tube heat exchanger

Heat exchangers are extensively used in various industries. In this study, the impact of geometric and flow parameters on the performance of a shell and double helical coil heat exchanger is studied numerically. The investigated geometric parameters include external coil pitch, internal coil pitch, internal coil diameter, and coil diameter. The influences of considered geometrical parameters are analyzed on the output temperature of the hot and cold fluid, convective heat transfer coefficient, pressure drop, and average Nusselt number. Water is considered as working fluid in both shell and tube. As an innovation, double helical coils are used instead of one in the heat exchanger. To compare the obtained results accurately, in each section, the heat transfer area (coil outer surface) is kept constant in all models. The results show that the geometrical parameters of double helical coils significantly affect the heat transfer rate.     

A finite line source simulation model for geothermal systems with series- and parallel-connected boreholes and independent fluid loops

A model for the simulation of geothermal systems with parallel- and series-connected boreholes is presented. Mass and heat balance problems are formulated for each component in the system and are assembled into system-level problems. A third problem is formulated to account for heat transfer in the bore field, using the finite line source solution. This third problem is coupled to the system-level heat balance problem by an analytical solution of the heat transfer inside boreholes with multiple U-tubes. The simulation model allows for any number of independent fluid loops within the bore field or within individual boreholes and allows for combinations of specified inlet fluid temperatures and heat extraction rates in independent fluid loops. The model accounts for the axial variation of the fluid and borehole wall temperatures and heat extraction rates. The capabilities of the model are demonstrated through three example simulations.     

100 MeV质子回旋加速器二期辐照效应管道设计

针对中国原子能科学研究院100 MeV质子回旋加速器上的单粒子效应辐照装置进行了二期管道设计，采用八极磁铁校正法对束流进行了扩束及均匀化，最终在靶上得到了一个30 cm×30 cm、均匀性好于92%的均匀分布的束斑，满足了单粒子效应实验的需求。为降低靶站处的束流能散及中子本底，采用两级降能的方案，在偏转磁铁前放置1个降能片，将能量分为100 MeV和40 MeV两档，并分别针对这两个能量点进行方案设计，束流利用率均在42%以上。公差分析结果表明，四极磁铁对靶上束斑均匀性的影响大于八极磁铁，安装过程中应优先保证四极磁铁的安装公差。     

Thermal Management Enables Bright and Stable Perovskite Light-Emitting Diodes

The performance of lead-halide perovskite light-emitting diodes (LEDs) has increased rapidly in recent years. However, most reports feature devices operated at relatively small current densities (<500 mA cm⁻²) with moderate radiance (<400 W sr⁻¹ m⁻²). Here, Joule heating and inefficient thermal dissipation are shown to be major obstacles toward high radiance and long lifetime. Several thermal management strategies are proposed in this work, such as doping charge-transport layers, optimizing device geometry, and attaching heat spreaders and sinks. Combining these strategies, high-performance perovskite LEDs are demonstrated with maximum radiance of 2555 W sr⁻¹ m⁻², peak external quantum efficiency (EQE) of 17%, considerably reduced EQE roll-off (EQE > 10% to current densities as high as 2000 mA cm⁻²), and tenfold increase in operational lifetime (when driven at 100 mA cm⁻²). Furthermore, with proper thermal management, a maximum current density of 2.5 kA cm⁻² and an EQE of ≈1% at 1 kA cm⁻² are shown using electrical pulses, which represents an important milestone toward electrically driven perovskite lasers.     

Pure CuBi2O4 Photoelectrodes with Increased Stability by Rapid Thermal Processing of Bi2O3/CuO Grown by Pulsed Laser Deposition

A new method for enhancing the charge separation and photo‐electrochemical stability of CuBi₂O₄ photoelectrodes by sequentially depositing Bi₂O₃ and CuO layers on fluorine‐doped tin oxide substrates with pulsed laser deposition (PLD), followed by rapid thermal processing (RTP), resulting in phase‐pure, highly crystalline films after 10 min at 650 °C, is reported. Conventional furnace annealing of similar films for 72 h at 500 °C do not result in phase‐pure CuBi₂O₄. The combined PLD and RTP approach allow excellent control of the Bi:Cu stoichiometry and results in photoelectrodes with superior electronic properties compared to photoelectrodes fabricated through spray pyrolysis. The low photocurrents of the CuBi₂O₄ photocathodes fabricated through PLD/RTP in this study are primarily attributed to their low specific surface area, lack of CuO impurities, and limited, slow charge transport in the undoped films. Bare (without protection layers) CuBi₂O₄ photoelectrodes made with PLD/RTP shows a photocurrent decrease of only 26% after 5 h, which represents the highest stability reported to date for this material. The PLD/RTP fabrication approach offers new possibilities of fabricating complex metal oxides photoelectrodes with a high degree of crystallinity and good electronic properties at higher temperatures than the thermal stability of glass‐based transparent conductive substrates would allow.     

A new ternary phase in the system CaO–Al2O3–Cr2O3: Crystal structure and thermal expansion of CaAl2Cr2O7

Polycrystalline material of a novel phase in the system CaO–Al₂O₃–Cr₂O₃ has been obtained by solid-state reactions. Chemical analysis indicated the composition CaAl₂Cr₂O₇. Single-crystal growth of the new compound using borax as a mineralizer was successful. Diffraction experiments at ambient conditions on a crystal with composition CaAl_2.13Cr_1.87O₇ yielded the following basic crystallographic data: space group P 3, a = 7.7690(5) Å, c = 7.6463(5) Å, V = 399.68(6) ų, Z = 3. Structure determination and subsequent least-squares refinements resulted in a residual of R(|F|) = 2.3% for 1440 independent observed reflections and 113 parameters. To the best of our knowledge, the structure of CaAl_2.13Cr_1.87O₇ or CaAl₂Cr₂O₇ represents a new structure type. It belongs to the group of double layer structures where individual double layers contain octahedrally and tetrahedrally coordinated cation positions. Linkage between neighboring sheet packages is provided by additional calcium cations. Furthermore, thermal expansion has been studied in the interval between 29 and 790°C using in situ high-temperature single-crystal diffraction. No indications for a structural phase transition were observed. From the evolution of the lattice parameters the thermal expansion tensor has been obtained. A pronounced anisotropy is evident. The response of structural building units to variable temperature has been discussed.